3 Auf- The exact knowledge of incipient-melting temperatures is especially desirable in hypereutec-
zeiten tic steels since melting of ledeburite can occur during hot forming or heat treatment of these
steels.
The possibility of immediate application of the incipient-melting temperatures, as deter-
mined in the high temperature microscope; to checking the behaviour of high speed steels at
the hardening temperature was thoroughly investigated by microstructure determination of
sich im hardness samples. The results of these investigations agree excellently with the corresponding
zestellt melting temperatures.
daher, Since one has to expect a decrease in toughness for hardening at temperatures above the
en und incipient-melting point, torsion tests were casried out to show if in this case the performance
of tools is considerably affected.
lischen The machining tests were performed on an austenitic Cr-Ni steel with straight turning tools
Stähle made of steel S 10—4—3—10, whose rake angles were of different magnitude. At too low
rake angles an increased wear is noticed regardless of the selected hardening temperature.
roskop With increasing rake angle the toughness of the material is used in an increasing way. Thus
arbeits- the wear resistance at decreased toughness is negatively influenced as a concequence of too
proben high hardening temperatures.
Is fest- If good toughness properties are required, it is thus necessary not to exceed the onset-
5 melting temperature during hardening, and to achieve the desired high hardness of the tools
igkeits- by prolonged dipping times.
rch das
eln aus
Bei zu 1 R. Mitsche, F. Jeglitsch, F. Gabler, Möglichkei- 6 W. Peter, H. Finkler, E. Kohlhaas, Entstehung
n über- ten und Grenzen der heutigen Hochtemperatur- und Beseitigung besonderer Karbidseigerungen
n Maße mikroskopie, in Werkzeugstählen mit rd. 1 % C,
dert Berg- und hüttenmänn. Mh 109 (1964) 110/14 Archiv Eisenhüttenwes. 41 (1970) 749/56
n r er 2 G. Reinacher, Hochtemperaturmikroskopische / S. Wilmes, Zähigkeitsuntersuchungen an
chteilig Bestimmung der Solidustemperaturen von Iri- Schnellarbeitsstählen,
dium-Legierungen mit etwa 1 % B, P und Si Stahl u. Eisen 81 (1961) 676/84
hmel Metall 19 (1965) 707/11 8 K. Krekeler, Die Leistung von gegossenen und
zaıne 27 3 F. Jeglitsch, Beitrag zum Oberflächenschmelzen warmverformten Werkzeugen aus Schnellar-
r Werk- und -erstarren, beitsstahl und ihre metallurgischen Grundlagen,
Prakt. Metallographie 4 (1967) 53/64 Stahl u. Eisen 78 (1958) 676/85
+ 4. Kulmburg, R. Blöch, K. Swoboda, E. Plöck- 9 O0. Mülders, E. Nickel, Eigenschaften von
inger, Besondere Anwendungsbeispiele der Schnellarbeitsstählen im Gußzustand,
Hochtemperaturmikroskopie, DEW — Techn. Berichte 2 (1962) 7/15
_ Berg- und hüttenmänn. Mh 109 (1964) 114/19 10 E. Kunze, E. Horn, Zusammenhang zwischen
5 A. Kulmburg, F. Gabler, F. Korntheuer, Zusatz- Erstarrungsverlauf und Gefügeausbildung von
einrichtungen für die Hochtemperaturmikro- Schnellarbeitsstählen
skopie und praktische Anwendung, DEW — Techn. Berichte 1 (Gl 961) 6 /1 5
Radex-Rundschau (1967) 723/26 11 Stahl-Eisen-Werkstoffblatt 320/69
Schnellarbeitsstähle
‚ effects
on. It is
for the
419